During an earthquake, soft ground amplifies shaking compared with rock. Modern seismic codes therefore classify sites by ground stiffness, and the most common measure is Vs30. This article explains what Vs30 is, how it is measured and how it is used in seismic site classification.
What is Vs30?
Vs30 is the time-averaged shear-wave velocity of the top 30 metres of the ground. It is not a simple average of velocities. It is calculated from the time a shear wave takes to travel through the top 30 m:
Vs30 = 30 / Σ (hi / Vsi)
where hi is the thickness and Vsi the shear-wave velocity of each layer. Slow layers have a strong influence, which reflects their effect on shaking.
Why ground type matters
Seismic waves slow down and increase in amplitude as they pass from stiff rock into softer soils. Soft deposits can also resonate at certain frequencies, causing much stronger shaking than on nearby rock, as seen in many past earthquakes around the world. Design forces must account for this.
Site classes
Eurocode 8 uses ground types based mainly on Vs30. In simplified form:
| Ground type | Description | Vs30 (m/s) |
|---|---|---|
| A | Rock or rock-like formation | over 800 |
| B | Very dense sand, gravel or very stiff clay | 360 to 800 |
| C | Dense or medium dense sand, gravel or stiff clay | 180 to 360 |
| D | Loose to medium cohesionless soil or soft to firm clay | below 180 |
| E | Thin soft alluvium over stiffer material | special case |
Other codes, such as those based on ASCE 7, use similar classes with slightly different boundaries. Special studies are needed for liquefiable or very soft soils.
How Vs30 is measured
- MASW: active and passive surface wave surveys, quick and economical.
- Refraction microtremor and other passive methods: useful in urban areas.
- Downhole and crosshole tests: in boreholes, giving direct measurements.
- Seismic cone penetration tests (SCPT) in suitable soils.
Correlations with SPT N-values exist but are less reliable than direct measurement.
Seismicity in East Africa
The East African Rift System is tectonically active, with earthquakes recorded along the Rift in Kenya and neighbouring countries. Northern Somalia lies near the active Gulf of Aden spreading zone. Seismic design is therefore relevant for high-rise buildings, hospitals, bridges, dams and industrial facilities. Kenyan practice increasingly uses Eurocode-based seismic design for significant structures.
Using Vs30 in design
- Selecting the ground type and corresponding response spectrum.
- Identifying sites needing site-specific response analysis.
- Flagging liquefaction or soft soil hazards for further study.
- Informing foundation design for dynamic loads.
Practical tips
- Measure, rather than assume, Vs30 for important structures.
- Check that the survey reaches 30 m or more.
- Use several profiles across larger sites.
- Calibrate with borehole logs.
How Quantum Geoconsultants can help
We measure Vs30 with MASW and provide seismic ground type classifications for design. See MASW surveys, investigations for high-rise buildings and fault detection surveys.
Frequently asked questions
What is Vs30?
Vs30 is the time-averaged shear-wave velocity of the top 30 metres of ground, used to classify sites for seismic design.
How is Vs30 measured?
Usually with MASW or other surface wave methods, or with downhole and crosshole seismic tests in boreholes.
Does East Africa need seismic design?
Yes. The East African Rift is seismically active, and areas near the Gulf of Aden also experience earthquakes, so seismic design is important for many structures.
📡 Request a geophysical survey quote
The cost of a geophysical survey depends mainly on the area or length of survey lines, the methods and depth of investigation needed, and site access. Tell us about your project and we will propose a survey design and quotation.
We reply with a proposed survey design and quotation. Prices are not listed online because every site and target is different.
Plan your geophysical survey
Tell us your site, target and depth of interest. We will recommend the right methods and send a survey design and quotation.