Collecting resistivity data is only half the job. Interpretation turns numbers and colours into a decision about where and how deep to drill. This article explains how hydrogeologists read VES curves and ERT sections for aquifer identification.
Start with the geology
The same resistivity value can mean different things in different rocks. Interpretation begins with the geological setting, known lithologies and records of nearby boreholes, including their depths, water strikes and water quality.
Resistivity signatures by setting
Crystalline basement
Typical sequence: dry or lateritic topsoil (moderate to high), weathered zone (low to moderate), fractured transition (moderate), fresh rock (very high). Good targets have a thick, moderately low weathered zone, or a vertical low-resistivity fracture zone cutting the fresh rock on ERT. Very low values may indicate clay-rich weathering with poor yield.
Volcanic rocks
Dense lavas are resistive; weathered horizons, tuffs and fractured or vesicular zones between flows are less resistive and often water-bearing. In parts of Kenya’s Rift Valley, low resistivity may also reflect hydrothermally altered clays or mineralised water.
Sedimentary basins
Sands and gravels with fresh water show moderate resistivity; clays are low; saline sands are very low. Interpretation focuses on identifying sand units and the depth of any saline water.
Coastal settings
Fresh water lenses in sands and limestone show moderate resistivity above very low-resistivity saline water. See coastal groundwater exploration with resistivity.
Reading VES curves
- Identify the curve type and number of layers.
- Invert to a layered model, and test alternative models within equivalence limits.
- Assign geology to each layer using known values.
- Note the thickness and resistivity of the probable aquifer layer.
Reading ERT sections
- Check the data fit (RMS error) and the depth of reliable resolution.
- Look for continuous layers and lateral changes.
- Identify vertical low-resistivity features in resistive rock as possible fractures.
- Look for buried channels as low-resistivity troughs in high-resistivity bedrock.
- Watch for artefacts near the ends and bottom of sections.
Common pitfalls
- Clay versus water: both are conductive. Very low values often mean clay or salt, not a productive aquifer.
- Equivalence: a thin conductive layer can look like a thicker, less conductive one.
- 3D effects: features beside the line can appear beneath it.
- Cultural noise: pipes, fences and power lines create false anomalies.
- Over-interpreting small features below the resolution limit.
Ranking drilling points
Targets are ranked by combining:
- Thickness and resistivity of the probable aquifer zone
- Presence of fractures or channels
- Depth to target and drilling cost
- Water quality risk (very low values may indicate salinity)
- Access, distance to point of use and contamination sources
Learning from results
Comparing interpretations with drilling logs and yields improves future interpretation. Over time, local resistivity-yield relationships become a powerful tool. See integrating geophysics and drilling.
How Quantum Geoconsultants can help
Our hydrogeologists interpret resistivity data with local geological knowledge and borehole records. See hydrogeological surveys, ERT and VES.
Frequently asked questions
Does low resistivity always mean water?
No. Low resistivity can mean clay, saline water or a good aquifer. Geology and local borehole data are needed to tell them apart.
What is a good resistivity for an aquifer?
It depends on the geology and water salinity. In many East African settings, fresh-water aquifers show moderate values, between those of clay and fresh rock.
Why combine several survey lines?
Several lines show whether a feature is continuous, such as a fracture zone, and help choose the best drilling point.
📡 Request a geophysical survey quote
The cost of a geophysical survey depends mainly on the area or length of survey lines, the methods and depth of investigation needed, and site access. Tell us about your project and we will propose a survey design and quotation.
We reply with a proposed survey design and quotation. Prices are not listed online because every site and target is different.
Plan your geophysical survey
Tell us your site, target and depth of interest. We will recommend the right methods and send a survey design and quotation.