Electrical Resistivity Tomography (ERT) produces a 2D image of the ground’s resistivity beneath a line. It has largely replaced single-point soundings where ground conditions change sideways, such as fractured rock, cavities and faults. This article explains how an ERT survey works and where it is most useful.
How ERT data are collected
Dozens of electrodes, often 48 to 96 or more, are placed at equal spacing along a line and connected by multi-core cables to a switching resistivity meter. The instrument automatically selects combinations of four electrodes and records hundreds or thousands of measurements at different positions and depths. Lines can be extended by roll-along to cover long profiles.
Choosing the array
- Wenner: robust signal, good for horizontal layers.
- Wenner-Schlumberger: a good compromise for layers and lateral changes.
- Dipole-dipole: best for vertical features such as fractures and dykes, but more sensitive to noise.
- Gradient arrays: efficient with multi-channel instruments.
Depth and resolution
Depth of investigation is roughly a fifth to a quarter of the total spread. Resolution is best near the surface and decreases with depth, roughly in proportion to electrode spacing. Small electrode spacing gives detail but limited depth; larger spacing reaches deeper with less detail. The design balances both for the target.
Inversion
Measured apparent resistivities are not a picture of the ground. Inversion software (for example RES2DINV or similar) iteratively adjusts a model of the subsurface until calculated data match the field data. The fit is measured by an RMS error. Good practice includes:
- Removing bad data points before inversion.
- Including topography.
- Testing different inversion settings (smooth versus blocky) to see which features are robust.
- Showing sensitivity or depth of investigation limits on the section.
Reading an ERT section
Sections are usually coloured from blue (low resistivity) to red or purple (high). Typical features:
- Low-resistivity layers: clay, saturated weathered rock or saline water.
- High-resistivity layers: fresh rock, dry sand, or air-filled voids.
- Vertical low-resistivity zones in resistive rock: water-bearing fractures or faults.
- Isolated high or low anomalies: cavities (air-filled high, water or clay-filled low).
See interpretation of resistivity profiles.
Applications
- Groundwater: locating fracture zones and buried channels for boreholes.
- Cavity detection: in coral limestone and gypsum. See our cavity detection surveys.
- Fault detection: in the Rift Valley and other active areas. See fault detection surveys.
- Depth to bedrock for foundations and excavations.
- Dams and embankments: seepage paths and weak zones.
- Landslides: slip surfaces and water content.
- Landfills and contamination: plume mapping.
3D and time-lapse ERT
Grids of lines or electrodes produce 3D models for complex sites. Repeating surveys over time (time-lapse) shows changes such as seepage, saline intrusion or grout movement.
Limitations
ERT is affected by electrode contact in dry or rocky ground, cultural noise, and 3D effects when lines run near structures. Like all geophysics, it is non-unique and needs calibration with boreholes. See limitations of geophysical surveys.
How Quantum Geoconsultants can help
We design and run ERT surveys for groundwater, construction and hazard assessment. See our ERT surveys in Kenya, geophysics for construction and geophysical surveys in Somalia.
Frequently asked questions
What does an ERT survey produce?
A 2D cross-section of resistivity beneath a survey line, showing layers, fractures, voids, water and clay zones.
How deep can ERT image?
Roughly a fifth to a quarter of the total electrode spread, so a 400 m line may image around 70 to 100 m deep, depending on array and conditions.
What is inversion?
Inversion is the computer process that finds a resistivity model of the ground that best explains the measured apparent resistivities.
📡 Request a geophysical survey quote
The cost of a geophysical survey depends mainly on the area or length of survey lines, the methods and depth of investigation needed, and site access. Tell us about your project and we will propose a survey design and quotation.
We reply with a proposed survey design and quotation. Prices are not listed online because every site and target is different.
Plan your geophysical survey
Tell us your site, target and depth of interest. We will recommend the right methods and send a survey design and quotation.