The electrical resistivity survey is the most widely used geophysical method for groundwater detection in Kenya and East Africa. It is relatively low-cost, portable and effective at revealing the layers and fractures that host aquifers. This article explains how it works and how it guides borehole siting.
What resistivity measures
Resistivity describes how strongly a material resists electric current. Dry rock resists current strongly, while water with dissolved salts, and clay minerals, conduct it well. In most rocks, current flows mainly through water in pores and fractures, so resistivity depends on how much water there is, how salty it is, and how much clay is present.
Typical resistivity ranges
Values vary widely, but approximate ranges are:
| Material | Approximate resistivity (ohm-m) |
|---|---|
| Saline groundwater or saline sediments | below 5 |
| Clay | 1 to 30 |
| Saturated sand and gravel (fresh water) | 30 to 300 |
| Weathered or fractured basement rock | 50 to 500 |
| Dry sand and gravel | several hundred to thousands |
| Fresh crystalline rock | over 1,000 |
Because ranges overlap, a low value could be clay, salty water or a good aquifer. Interpretation must use local geology and borehole records.
How measurements are made
Current is passed into the ground through two electrodes, and the voltage is measured between two others. From current, voltage and electrode geometry, the apparent resistivity is calculated. Widening the electrode spread sends current deeper, so measurements at increasing spacings reveal deeper layers. See apparent and true resistivity.
VES: one point, many depths
Vertical Electrical Sounding expands the electrodes around a fixed centre, usually with the Schlumberger array. The result is a curve that is interpreted as a layered model: for example, dry soil, clay, weathered rock and fresh rock. VES is quick and effective where layers are fairly flat, such as sedimentary basins and weathered basement.
ERT: a 2D picture
Electrical Resistivity Tomography uses many electrodes along a line, switched automatically, and inversion software produces a 2D section. ERT is excellent for finding vertical fracture zones in basement rock and volcanics, buried channels and saline boundaries, which VES can miss.
Profiling
Constant-spacing traverses measure resistivity along a line at a fixed depth, helping locate fracture zones before detailed soundings.
What makes a good drilling target?
- A thick, moderately low resistivity zone beneath higher-resistivity cover, indicating saturated weathered or fractured rock.
- A narrow vertical low-resistivity zone in high-resistivity rock on ERT, suggesting a water-bearing fracture.
- Sand and gravel layers with moderate resistivity in sedimentary sequences.
- Avoiding very low values that may indicate thick clay or saline water.
See interpreting resistivity profiles.
Common settings in East Africa
- Basement areas (Machakos, Kitui, Makueni, parts of Somalia): targets are weathered zones and fractures.
- Volcanic areas (Nairobi, Rift Valley): water occurs in fractured lavas and between flows.
- Sedimentary basins (northern and coastal Kenya, much of Somalia): targets are sand layers, with care to avoid saline zones.
Limitations
Resistivity cannot distinguish clay from saline water on its own, can be affected by power lines and metal pipes, and becomes less precise with depth. Combining it with geology and other methods such as electromagnetic surveys improves results.
How Quantum Geoconsultants can help
We carry out VES and ERT surveys for borehole siting across Kenya and Somalia. See our hydrogeological surveys, ERT surveys and guide to hydrogeological surveys.
Frequently asked questions
Can a resistivity survey find water directly?
No. It measures how easily electric current passes through the ground. Water-bearing layers often have characteristic resistivity, so interpretation with geology indicates where aquifers are likely.
How deep can a resistivity survey see?
Depth depends on the electrode spread. Typical groundwater surveys investigate from tens of metres to around 150 to 250 m, with longer spreads reaching deeper.
Why do clay and salty water show low resistivity?
Clay minerals and dissolved salts conduct electricity well, so both lower resistivity. This is why interpretation must consider the local geology.
💧 Water demand calculator
How much water does your borehole need to deliver each day? Enter your numbers for a quick planning estimate.
Rough planning figures only, using typical daily use per person and per animal, with one day of storage and about 6 hours of good sun. Your test pumping result sets the final pump size.
Send these numbers on WhatsAppGet a borehole quote for Kenya
Send us your location. We will advise on the survey, permits, expected depth and the full cost up to a working solar borehole.