Get a Quote
← All articles

Solar-Powered Borehole Pumping Systems: Design and Installation

How to design and install a solar-powered borehole pumping system: water demand, head, solar array sizing, pumps and controllers, storage, mounting, protection and maintenance.

By Quantum Geoconsultants pump installation teamUpdated 19 November 20262 min read
TopsoilLava flowOlder lavas & tuffsStatic water level (pump off) Pumping water level ◀ Submersible pump & motor ◀ Screen below the pump Pump sized from test pumping

⚙️ Borehole Pumps & Solar: a technical article by the Quantum Geoconsultants pump installation team.

Kenya and Somalia have excellent sunshine, making solar borehole pumps one of the most cost-effective ways to supply water. With no fuel or electricity bills, a well-designed solar pumping system can run for many years. This article explains design and installation.

How a solar pumping system works

  1. Solar panels produce DC electricity.
  2. A controller or solar pump inverter manages power and protects the pump.
  3. The submersible pump lifts water during daylight.
  4. Water is stored in a tank for use day and night.

Step 1: Daily water demand

Estimate total daily use in cubic metres. See determining pumping capacity.

Step 2: Total dynamic head

Calculate lift from the dynamic water level to the tank inlet plus friction. See TDH and flow rate.

Step 3: Check the borehole

Solar pumps deliver most water around midday. Peak flow must not exceed the safe yield. See borehole yield.

Step 4: Size the solar array

The hydraulic energy needed per day is approximately:

Energy (Wh/day) ≈ 2.725 × daily volume (m³) × head (m)

The array size then depends on peak sun hours (often around 5 to 6 in much of Kenya) and overall system efficiency (pump, motor, controller and losses, often in the range of 40 to 50 percent).

Example: 20 m³/day at 80 m head needs about 2.725 × 20 × 80 ≈ 4,360 Wh of hydraulic energy. With 5.5 sun hours and 45 percent efficiency, the array would be roughly 4,360 ÷ (5.5 × 0.45) ≈ 1,760 W, so about 1.8 to 2 kW of panels, plus a margin for cloudy days and panel ageing.

Step 5: Choose pump and controller

Controllers use MPPT to get the most power from the panels. See solar controllers and MPPT.

Step 6: Storage

Size the tank for at least one day of demand, often more for cloudy periods. See tank sizing.

Installation

Maintenance

Clean panels regularly, check connections and monitor flow. Solar systems have few moving parts beyond the pump. See pump maintenance.

How Quantum Geoconsultants can help

We design and install solar borehole systems sized from test pumping data. See borehole solar installation in Kenya and solar versus electric pumps.

Frequently asked questions

How many solar panels does a borehole pump need?

It depends on daily water demand, total head and sunshine. Higher demand and deeper water need more panels. A hydraulic calculation gives the array size.

Do solar pumps need batteries?

Usually not. Water is stored in a tank instead, which is cheaper and more durable than batteries.

Do solar pumps work on cloudy days?

They pump less on cloudy days, which is why storage and a margin in array size are important.

⚙️ Borehole pump size calculator

Enter your borehole's numbers from the test pumping report (or your best estimate) to see the total head, the flow and roughly how big a submersible pump or solar array you need.

0total head (m)
0pump flow (m³/hour)
0solar array (watts)

Rough planning figures only. Total head = pumping water level + tank height + an allowance for pipe friction. The final pump is chosen from the manufacturer's pump curves, your test pumping yield and your water quality.

Get a borehole pump installation quote

Send us your test pumping report, borehole depth and where the tank will sit. We will size the right submersible or solar pump and send a quotation for supply, installation and commissioning.

💬 WhatsApp