Get a Quote
← All articles

Understanding Static Water Level, Dynamic Water Level and Drawdown

Clear explanations of static water level, dynamic water level, drawdown, specific capacity and recovery, and why they matter for pump selection and borehole management.

By Quantum Geoconsultants hydrogeology teamUpdated 19 November 20262 min read
TopsoilLava flowFractured lava flowWater between lava flowsOlder lavas & tuffs Depth set by the survey

💧 Hydrogeology & Boreholes: a technical article by the Quantum Geoconsultants hydrogeology team.

Borehole reports are full of water level terms. Understanding static water level, dynamic water level and drawdown helps you read test pumping results, choose the right pump and manage your borehole well.

Static water level (SWL)

The static water level, or rest water level, is the depth from the ground (or casing top) to the water surface when the borehole has not been pumped for long enough to recover fully. It reflects the natural groundwater level or pressure in the aquifer.

In a confined aquifer, the static level can be well above the top of the aquifer, and occasionally above ground (artesian flow).

Dynamic water level (DWL)

When pumping starts, water flows towards the borehole and the level inside drops. The water level during pumping is the dynamic water level, or pumping water level. It depends on the pumping rate, how long the pump has run, aquifer properties and borehole efficiency.

Drawdown

Drawdown is the difference between static and dynamic levels:

Drawdown = dynamic water level − static water level

For example, if the static level is 40 m and the pumping level is 58 m, the drawdown is 18 m. Drawdown increases with higher pumping rates and over time, and it may stabilise if the aquifer receives recharge.

Specific capacity

Specific capacity is the pumping rate divided by drawdown, for example 5 m³/h ÷ 10 m = 0.5 m³/h per metre. It allows boreholes to be compared and shows when performance declines due to clogging.

Residual drawdown and recovery

After pumping stops, water levels rise again. The remaining difference from the static level is residual drawdown. Slow or incomplete recovery can indicate limited aquifer storage or recharge, an important warning for sustainability.

The cone of depression

Pumping creates a cone-shaped lowering of the water table or pressure around the borehole. Neighbouring boreholes within the cone may see their levels fall, which is why spacing and abstraction limits matter. See sustainable groundwater development.

Why these levels matter for the pump

Seasonal and long-term changes

Static levels in East Africa often rise during the long and short rains and fall in dry seasons. Over years, heavy pumping in an area can cause long-term declines, as seen in parts of Nairobi. Regular measurements build a record that warns of problems early.

How to measure water levels

Water levels are measured with an electric dip meter lowered down an access tube, or with pressure transducers and data loggers. Installing an access tube alongside the rising main makes routine measurement easy and safe.

How Quantum Geoconsultants can help

We measure and interpret water levels during test pumping and install monitoring for long-term management. See pumping tests, water levels and pump submergence and pump installation.

Frequently asked questions

What is the static water level?

It is the level at which water stands in a borehole when it has not been pumped for some time.

What is the dynamic water level?

It is the water level in the borehole while it is being pumped. It is lower than the static level.

What is drawdown?

Drawdown is the difference between the static and dynamic water levels. It increases with pumping rate and time.

💧 Water demand calculator

How much water does your borehole need to deliver each day? Enter your numbers for a quick planning estimate.

0litres per day
0suggested tank (litres)
0pump flow (m³/hour, solar)

Rough planning figures only, using typical daily use per person and per animal, with one day of storage and about 6 hours of good sun. Your test pumping result sets the final pump size.

Get a borehole quote for Kenya

Send us your location. We will advise on the survey, permits, expected depth and the full cost up to a working solar borehole.

💬 WhatsApp