Most borehole test programmes include two main tests: a step drawdown test and a constant discharge test. Each answers different questions. Together they give the information needed to set a safe yield and design the pump. This article explains both.
The step drawdown test
Purpose
To measure how drawdown responds to increasing pumping rates and to assess borehole performance.
Procedure
- Measure the static water level.
- Pump at a low rate for a fixed period, commonly 60 to 100 minutes.
- Without stopping, increase to the next rate for the same period.
- Repeat for typically four or five steps, up to the maximum expected rate.
- Measure water level frequently in each step and keep each rate steady.
- Measure recovery after pumping stops.
Analysis
Drawdown in a pumped borehole has two parts:
- Aquifer loss, roughly proportional to pumping rate (BQ).
- Well loss, caused by turbulent flow through the screen and pack, increasing faster (roughly CQ²).
Plotting specific drawdown (drawdown divided by rate) against rate gives B and C (the Jacob method). From these, the engineer calculates borehole efficiency and predicts drawdown at any rate. High well losses suggest poor development or screen design.
The constant discharge test
Purpose
To measure long-term aquifer response, determine transmissivity and storativity, and identify boundaries or recharge.
Procedure
- Allow water level to recover fully after the step test.
- Pump at a single steady rate, usually chosen from the step test results.
- Continue for typically 24 to 72 hours, longer for large supplies.
- Measure water level on a logarithmic schedule: every minute at first, then every few minutes, then hourly.
- Measure rate regularly; keep it constant within a few percent.
- Monitor conductivity and take water samples.
- Record recovery after the pump stops.
Analysis
Drawdown plotted against log time often forms a straight line in its later part. The Cooper-Jacob method uses the slope of this line to calculate transmissivity. Changes in slope reveal:
- Steepening: a barrier boundary such as the edge of a fracture zone, warning of falling levels over time.
- Flattening: recharge, such as a river or leakage from another layer.
Recovery analysis (Theis recovery) provides an independent check.
Using the results
- Choose a production rate with an acceptable predicted drawdown.
- Set the pump intake depth with a safety margin above the screens.
- Estimate long-term water level decline.
- Identify whether rehabilitation could improve efficiency.
- Check that water quality remains stable during pumping.
A simple example
A step test at 2, 4, 6 and 8 m³/h shows drawdowns of 3, 7, 12 and 19 m. Drawdown increases faster than rate, showing significant well losses at high rates. The constant rate test at 5 m³/h for 24 hours stabilises at about 10 m. The hydrogeologist might recommend about 4 to 5 m³/h, with the pump set well below the dynamic level and above the screens.
How Quantum Geoconsultants can help
We run and analyse step and constant rate tests and turn the results into pump and solar designs. See pumping tests, pump installation and borehole solar installation.
Frequently asked questions
What does a step drawdown test show?
It shows how drawdown increases as pumping rate increases, separating losses in the aquifer from losses caused by the borehole itself.
How long should a constant discharge test run?
Typically 24 to 72 hours, long enough to see whether drawdown stabilises and to detect boundaries.
What is borehole efficiency?
It is the proportion of total drawdown caused by the aquifer rather than by losses at the screen and gravel pack. Higher efficiency means lower pumping costs.
💧 Water demand calculator
How much water does your borehole need to deliver each day? Enter your numbers for a quick planning estimate.
Rough planning figures only, using typical daily use per person and per animal, with one day of storage and about 6 hours of good sun. Your test pumping result sets the final pump size.
Send these numbers on WhatsAppGet a borehole quote for Kenya
Send us your location. We will advise on the survey, permits, expected depth and the full cost up to a working solar borehole.