Three properties describe how an aquifer behaves: hydraulic conductivity, transmissivity and storativity. They control how much water a borehole can deliver, how far drawdown spreads and how boreholes interact. This article explains what they are and how they are measured.
Hydraulic conductivity (K)
Hydraulic conductivity describes how easily water flows through a material, usually in metres per day. Approximate ranges:
| Material | Typical K (m/day) |
|---|---|
| Clay | less than 0.001 |
| Silt and fine sand | 0.01 to 1 |
| Clean sand | 1 to 50 |
| Gravel | 50 to over 1,000 |
| Fractured rock | very variable |
Transmissivity (T)
Transmissivity is hydraulic conductivity multiplied by saturated aquifer thickness (T = K × b), in square metres per day. It describes the ability of the whole aquifer to transmit water to a borehole. A thin, highly permeable aquifer and a thick, moderately permeable aquifer may have the same transmissivity. In fractured rock, where thickness is hard to define, transmissivity is the more useful measure.
Storativity (S) and specific yield
Storativity is the volume of water released from storage per unit area of aquifer per unit decline in head. It has no units.
- Confined aquifers release water by slight expansion of water and compression of the aquifer, so S is very small, often around 0.00001 to 0.001.
- Unconfined aquifers release water by draining pores. The equivalent property, specific yield, is much larger, often 0.01 to 0.3.
Determining the properties from pumping tests
Cooper-Jacob straight-line method
Late-time drawdown plotted against log time forms a straight line. Transmissivity is calculated from the drawdown change over one log cycle (Δs) and the pumping rate (Q):
T = 2.3 Q / (4π Δs)
With an observation borehole at a known distance, the time intercept of the line gives storativity.
Theis curve matching
Field data are matched to the Theis type curve for confined aquifers, giving T and S. Variants exist for leaky and unconfined aquifers.
Recovery analysis
The Theis recovery method uses residual drawdown after pumping stops and is less affected by pump fluctuations. It gives a useful check on T.
Other methods
- Slug tests: a sudden change in water level, by adding or removing a volume, gives K near the borehole. Quick but local.
- Packer tests: isolate zones in rock boreholes to measure K of specific intervals. See BS EN ISO 22282.
- Grain size correlations: estimate K of sands from grading, useful for early estimates.
- Laboratory permeameters: for soil samples.
How the properties are used
- Predicting drawdown at different rates and times.
- Designing well fields with adequate spacing.
- Estimating interference with neighbouring boreholes.
- Groundwater modelling and resource assessment.
- Dewatering design for excavations.
Limitations
Standard methods assume an idealised aquifer: uniform, infinite in extent and fully penetrated. Real aquifers, especially fractured rock, rarely fit perfectly. Experienced interpretation recognises boundaries, leakage and dual porosity.
How Quantum Geoconsultants can help
We analyse pumping test data to determine aquifer properties for borehole design, well fields and dewatering. See step and constant rate tests, understanding aquifers and our hydrogeological surveys.
Frequently asked questions
What is the difference between transmissivity and hydraulic conductivity?
Hydraulic conductivity describes how easily water flows through a material. Transmissivity is conductivity multiplied by aquifer thickness, describing the whole aquifer.
Can storativity be measured from a single borehole?
Not reliably. Storativity needs water level measurements in an observation borehole at a known distance from the pumped borehole.
What units are used?
Hydraulic conductivity is usually in metres per day, transmissivity in square metres per day, and storativity has no units.
💧 Water demand calculator
How much water does your borehole need to deliver each day? Enter your numbers for a quick planning estimate.
Rough planning figures only, using typical daily use per person and per animal, with one day of storage and about 6 hours of good sun. Your test pumping result sets the final pump size.
Send these numbers on WhatsAppGet a borehole quote for Kenya
Send us your location. We will advise on the survey, permits, expected depth and the full cost up to a working solar borehole.