This article is a practical companion to our guide on VES principles. It focuses on how a Vertical Electrical Sounding is actually run in the field for groundwater exploration, how data quality is controlled and how results become a drilling recommendation.
Planning the survey
- Review geology, nearby boreholes and satellite images to identify targets such as fracture zones, valleys or contacts.
- Choose several sounding points to compare, not just one.
- Plan spread directions along the strike of geological features and away from fences, pipes and power lines.
- Decide the maximum AB/2 needed for the target depth, and check there is space for it.
Equipment
- Resistivity meter (often with a current transmitter and stacking capability)
- Steel current electrodes and non-polarising or steel potential electrodes
- Reels of insulated cable
- Measuring tapes, GPS, hammers and water for wetting electrodes in dry ground
Field procedure with the Schlumberger array
- Mark the centre point and record its GPS position.
- Lay out the tape along the planned direction.
- Start with AB/2 of about 1 to 2 m and MN/2 small.
- Take readings at logarithmically spaced AB/2 values, for example 1, 1.5, 2, 3, 4, 6, 8, 10, 15, 20, 30, 40, 60, 80, 100, 150, 200 m.
- Increase MN when the voltage becomes too small, taking overlapping readings at two MN values to tie the curve segments.
- Plot the curve in the field as you go, so bad points can be repeated.
Controlling data quality
- Electrode contact: in dry soils, wet the electrodes with salty water or use several electrodes.
- Stacking: repeat measurements and average to reduce noise.
- Smooth curves: sudden jumps usually indicate a near-surface problem at one electrode or a cable issue.
- Shift at MN changes: overlapping readings let curve segments be joined properly.
Interpretation
- Inspect the curve shape (H, K, A, Q types) for a first idea of layering.
- Use inversion software to fit a layered model.
- Test alternative models, because equivalence allows different layer combinations to fit equally well.
- Translate resistivities into geology using local knowledge and borehole logs.
See interpretation of resistivity profiles for aquifer identification.
Typical interpretations in East Africa
- Basement areas: high-resistivity topsoil, low-resistivity weathered zone, very high-resistivity fresh rock. The thickness and resistivity of the weathered zone guide site choice.
- Volcanic areas: alternating layers of lavas, tuffs and weathered horizons; moderately low zones beneath dense lavas may indicate aquifers.
- Sedimentary areas: sands of moderate resistivity between clays; very low values may indicate saline water.
From results to a drilling recommendation
The hydrogeologist ranks the sounding points by aquifer thickness, resistivity and depth, combined with geological reasoning, and recommends the best point, an expected water-bearing depth and a drilling depth. Uncertainty should be stated honestly.
When to combine VES with other methods
Where water is in narrow vertical fractures, VES alone may miss the target. Combining it with ERT, profiling or electromagnetic traverses greatly improves success.
How Quantum Geoconsultants can help
We run VES and ERT surveys and prepare reports for WRA applications. See hydrogeological surveys in Kenya and geophysical surveys.
Frequently asked questions
How long does a VES take?
A single sounding to moderate depth usually takes one to two hours, depending on spread length, terrain and data quality.
How many VES points are needed?
Usually several, often three to six or more on a site, so that candidate points can be compared and ranked.
Can VES give an exact drilling depth?
It gives an estimate of layer depths. The final depth is confirmed from drilling, water strikes and airlift yields.
📡 Request a geophysical survey quote
The cost of a geophysical survey depends mainly on the area or length of survey lines, the methods and depth of investigation needed, and site access. Tell us about your project and we will propose a survey design and quotation.
We reply with a proposed survey design and quotation. Prices are not listed online because every site and target is different.
Plan your geophysical survey
Tell us your site, target and depth of interest. We will recommend the right methods and send a survey design and quotation.