Borehole flushing in Tana River restores boreholes that have lost water, started pumping sand or turned brown. We clean out silt, scale and iron bacteria with compressed air and surging, then disinfect the borehole and measure the restored yield. This guide explains why boreholes in Tana River lose yield, how we flush them and what affects the cost, including mobilisation from our Nairobi base.
Signs your borehole in Tana River needs flushing
- Less water than before: the tank fills more slowly or the pump runs dry sooner
- Sand, silt or muddy water at the taps
- Brown, red or slimy water, or orange deposits
- White crusts from hard water
- The pump trips or fails often
- The borehole is shallower than drilled, because silt has filled the bottom
Why boreholes in Tana River lose yield
Many boreholes in Tana River draw water from river sands and gravels. Sand and silt gradually fill the borehole and clog the screens and gravel pack. Surging and air-lift flushing redevelop the screens and remove the sand, and a camera check confirms the screens are intact.
Some boreholes in Tana River produce sand, which fills the bottom of the borehole and wears out pumps. Flushing removes it, but if sand keeps coming the screen or gravel pack may be damaged, which our camera inspection will show.
Who we flush boreholes for in Tana River: Irrigation schemes around Hola and Bura, livestock keepers, schools and health centres, and homes and businesses in Hola, Garsen and Madogo.
Borehole flushing methods we use in Tana River
How we flush a borehole in Tana River
- Review the completion record, the original yield and the symptoms.
- Pull the pump and riser and inspect them for wear and deposits.
- Measure the depth and water level, and inspect with a camera where needed.
- Air-lift flush and surge zone by zone until the water runs clear.
- Inspect again with the camera where needed, to confirm the screens and bottom are clear.
- Disinfect the borehole by shock chlorination.
- Step test to measure the new yield and pumping water level.
- Reinstall or resize the pump, then report the before and after results.
If the pump needs replacing, see borehole pump installation in Tana River. It is also a good time to convert to solar: see borehole solar installation in Tana River.
When flushing is not enough
Flushing restores a clogged borehole, but it cannot create water that is not there. If the regional water level has fallen, the pump may need lowering or the borehole deepening. If the casing has collapsed or corroded, it may need relining. If the borehole was badly sited, a new hydrogeological survey in Tana River and borehole may be the better investment. Our measurements tell you which case you are in before you spend more.
Borehole flushing cost in Tana River, including mobilisation
The cost depends on the borehole depth and diameter, the methods needed (air-lift flushing alone, or with surging and a camera inspection), pump removal and reinstallation, the step test and site access.
We are based in Nairobi, so mobilisation costs change with the distance to your site. Tana River is far from our Nairobi base, so mobilisation is a bigger share of the cost. It covers long-haul transport of the compressor and crew and several nights of accommodation. Mobilisation is shown as a separate item in the quotation. Flushing several boreholes in the same area, or combining flushing with pump or solar work, shares one mobilisation.
We flush and rehabilitate boreholes across Tana River, including Hola, Garsen, Bura, Madogo, Kipini, Tarasaa, Bangale, Wenje.
Frequently asked questions
How much does borehole flushing cost in Tana River?
It depends on the borehole depth, the methods needed (air-lift flushing alone, or with surging and a camera inspection), pump removal and reinstallation, and the step test. Mobilisation from our Nairobi base is higher, as the county is far from Nairobi. Send us your borehole details for a quotation.
Why has my borehole in Tana River lost water?
Usually sand and silt filling the borehole and clogging the screens. Surging and air-lift flushing redevelop them.
How often should a borehole be flushed?
There is no fixed rule. Record the yield and water level every year, and flush when the yield drops noticeably or sand, discoloured water or pump problems appear. Iron-rich and hard-water boreholes usually need it more often.
Will flushing restore my borehole's full yield?
If the loss is caused by clogging, flushing often restores much of it. It cannot fix a falling regional water level, collapsed casing or a badly sited borehole. Our step test after flushing shows the restored yield.
Is the water safe to drink after flushing?
We disinfect the borehole by shock chlorination after flushing. Run the water to waste until the chlorine clears, and have the water tested before drinking.
References and further reading
- SSWM: well development and rehabilitation
- Global Water Partnership Eastern Africa: Kenya groundwater assessment results (2026)
- Barasa M. et al. (2018). Africa Groundwater Atlas: Hydrogeology of Kenya. British Geological Survey
- Water Resources Authority: water use allocation and permits
🩺 Borehole health check
Compare your borehole today with its completion record to see how much yield it has lost and how much silt has filled it. The original yield and depth are on the borehole completion record and test pumping report.
A rough guide only. A camera inspection and a step test after flushing show the real condition of the borehole.
Send these numbers on WhatsAppGet a borehole flushing quote in Tana River
Send us the borehole depth, its original and current yield and what the water looks like. We will recommend the right flushing method and send a quotation, including mobilisation from our Nairobi base.