Casing and screens form the permanent lining of a borehole. Poor choices here lead to collapsed holes, sand pumping, low yield and short borehole life. This article explains the requirements and best practice for borehole casing and well screen installation.
What casing and screens do
- Plain casing keeps the hole open and seals off unwanted zones such as clay, dry rock or poor-quality water.
- Screens are slotted sections placed opposite water-bearing zones that let water in while holding back sand and gravel.
- Together with the gravel pack and seal, they protect the borehole and the aquifer.
Casing materials
uPVC
The most common choice for water boreholes in Kenya. It does not corrode, is light and economical. It must have adequate wall thickness and pressure class for the depth, because collapse pressure increases with depth and during development.
Steel
Mild or galvanised steel is stronger and used for deep or large-diameter boreholes. It can corrode in saline or acidic water, shortening borehole life and causing iron problems.
Stainless steel
Durable and strong, with excellent screens, but costly. Used for high-value or corrosive settings.
Screen types
- Machine-slotted uPVC: common and economical.
- Wire-wound (continuous slot) screens: higher open area, better yield and efficiency, especially in fine sands.
- Bridge-slot and louvred steel screens: robust, used in some steel boreholes.
Slot size and open area
Slot size is chosen from the grain size of the aquifer and the gravel pack. Too wide and sand enters; too narrow and water entry is restricted and the screen clogs. Open area should be high enough that water enters at low velocity, which reduces head losses, sand movement and incrustation.
Placement
Screen placement comes from the drilling log, water strikes, airlift yields and geophysical logs. Best practice:
- Place screens opposite the productive zones only.
- Use plain casing opposite clays, unstable zones and saline layers.
- Do not screen the very top of the aquifer in unconfined conditions, where drawdown would expose it.
- Include a sump (plain casing with an end cap) at the bottom to collect fines.
Diameter
Casing diameter must suit the pump to be installed, with clearance for cables and rising main. Common water borehole casings are 4 to 6 inches (about 100 to 150 mm) internal diameter, with larger sizes for high-yield production wells.
Installation best practice
- Check the hole is clean, to depth and straight enough.
- Lay out and measure all casing and screen lengths in order.
- Join sections with proper threaded or solvent joints, not improvised fixings.
- Fit centralisers at intervals so casing stays central for an even gravel pack.
- Lower carefully without forcing. If it sticks, pull back and clean the hole.
- Record the final as-built design: depths of screens, casing, sump and pack.
Common mistakes
- Using thin, low-class pipe that collapses or deforms.
- Field-cut slots made with saws, which are uneven and weaken the pipe.
- Screens placed opposite clay or dry rock.
- No centralisers, giving a one-sided gravel pack and sand problems.
How Quantum Geoconsultants can help
Our hydrogeologists design casing and screen strings from drilling logs, and supervise installation. See borehole drilling, borehole drilling procedures and borehole camera inspection to check existing casing.
Frequently asked questions
Should a borehole use uPVC or steel casing?
uPVC is corrosion-resistant and common for most water boreholes. Steel is stronger and used for very deep boreholes or where high loads are expected, but it can corrode in aggressive water.
How is screen slot size chosen?
Slot size is matched to the aquifer grain size and gravel pack so water enters freely while sand is held back.
Where should screens be placed?
Opposite the water-bearing zones identified from drilling logs, with plain casing opposite clays and dry or poor-quality zones.
💧 Water demand calculator
How much water does your borehole need to deliver each day? Enter your numbers for a quick planning estimate.
Rough planning figures only, using typical daily use per person and per animal, with one day of storage and about 6 hours of good sun. Your test pumping result sets the final pump size.
Send these numbers on WhatsAppGet a borehole quote for Kenya
Send us your location. We will advise on the survey, permits, expected depth and the full cost up to a working solar borehole.