Get a Quote
← All articles

Understanding Soil Classification Under BS EN ISO 14688

How soils are identified, described and classified under BS EN ISO 14688: particle size fractions, description order, consistency, density and plasticity.

By Quantum Geoconsultants geotechnical teamUpdated 19 November 20263 min read
Black cotton soil: swells & shrinksFirmer weathered layerRock Core box Know your ground before you build

🏗️ Geotechnical Engineering: a technical article by the Quantum Geoconsultants geotechnical team.

A borehole log is only useful if everyone reads it the same way. BS EN ISO 14688 provides a common language for identifying, describing and classifying soils, and it is used together with the guidance in BS 5930. This article explains the key ideas.

The two parts of the standard

Rocks are covered separately by BS EN ISO 14689.

Particle size fractions

Fraction Particle size
Large boulders over 630 mm
Boulders 200 to 630 mm
Cobbles 63 to 200 mm
Gravel 2 to 63 mm
Sand 0.063 to 2 mm
Silt 0.002 to 0.063 mm
Clay finer than 0.002 mm

Gravel, sand and silt are further divided into coarse, medium and fine.

Coarse soils and fine soils

A key first step is to decide whether a soil behaves as a coarse soil (sand and gravel, where the grains control behaviour) or a fine soil (silt and clay, where plasticity and water content control behaviour). Even a modest amount of clay can make a soil behave as a fine soil, so the decision is based on behaviour, not just percentages.

The description order

A soil description follows a standard sequence. For a fine soil:

  1. Consistency (for example soft, firm, stiff)
  2. Structure (for example fissured, laminated)
  3. Colour
  4. Secondary constituents (for example slightly sandy)
  5. PRINCIPAL SOIL TYPE in capitals
  6. Minor constituents and other notes

Example: “Stiff fissured dark grey slightly gravelly CLAY of high plasticity.”

For a coarse soil, density replaces consistency: “Medium dense brown fine to medium SAND with some silt.”

Consistency of fine soils

Consistency is judged by hand tests in the field:

Laboratory or hand vane measurements of undrained shear strength support these descriptions.

Density of coarse soils

Density cannot be judged reliably by hand, so it is usually based on SPT N-values: very loose, loose, medium dense, dense and very dense.

Plasticity

Classification of fine soils relies on Atterberg limits from the laboratory. On the plasticity chart, the A-line separates clays (above) from silts (below), and the liquid limit sets the plasticity class: low, intermediate, high, very high or extremely high. Many East African red and black soils plot as high or very high plasticity clays. See BS 1377 laboratory tests.

Organic and made ground

Organic soils (peat, organic clays) are described separately because they are highly compressible. Made ground or fill, common on urban sites, is described with its constituents (for example concrete, brick, ash) because it can be loose, variable and contaminated.

Tropical and residual soils

Standard descriptions were developed mainly for transported soils in temperate climates. In tropical regions, residual soils formed by weathering in place, laterites and volcanic soils can behave differently from what their grading suggests. Good practice is to add notes on fabric, relict rock structure, cementation and sensitivity, and to rely on laboratory tests rather than appearance alone.

Why it matters

Consistent soil description reduces misunderstandings between the investigation team, designers and contractors. It is also the basis for choosing tests, selecting design parameters and comparing sites.

How Quantum Geoconsultants can help

Our engineering geologists log soils and rocks to BS 5930, BS EN ISO 14688 and 14689, supported by laboratory classification. Learn more about geotechnical site investigation or see our geotechnical surveys in Kenya.

Frequently asked questions

What does BS EN ISO 14688 cover?

Part 1 covers the identification and description of soils, and Part 2 sets out the principles for classifying them, including particle size fractions and plasticity.

What are the particle size limits for sand and gravel?

Sand is 0.063 to 2 mm and gravel is 2 to 63 mm. Silt is 0.002 to 0.063 mm and clay is finer than 0.002 mm.

Why is a standard soil description important?

It lets every engineer read a borehole log the same way, so designers, contractors and reviewers understand exactly what ground was found.

🏗️ Request a geotechnical survey quote

The scope and cost of a geotechnical investigation depend on the size and type of structure, the site area and the ground conditions. Tell us about your project and we will propose an investigation programme and quotation.

Under the National Building Code 2024, soil testing is now expected before construction. We reply with a proposed programme and quotation.

Book a geotechnical survey in Kenya

Know your ground before you build. Send us your site location and project details and we will propose an investigation programme and quotation.

💬 WhatsApp