Borehole pump installation in Kenya is where a borehole investment pays off or goes wrong. A pump that is too big empties the borehole and burns out, while one that is too small never delivers enough water. This guide explains how to choose and size a submersible borehole pump or solar borehole pump, how submersible pump installation is done properly, and how Kenya's geology and water quality change the right choice.
What is a borehole pump?
Almost every borehole in Kenya uses a submersible pump: a pump and electric motor joined into one long, narrow unit that hangs inside the borehole casing, below the water level. It pushes water up a riser pipe to a tank or straight into your pipework. Surface pumps can only lift water from a few metres down, so they rarely suit boreholes, which in Kenya are commonly tens to hundreds of metres deep.
Types of borehole pumps we install
How to size a borehole pump
Pump sizing needs three numbers. All of them come from the test pumping done at the end of drilling and from your site plan:
- Flow: how much water you need per day, divided by the hours of pumping. It must never be more than the borehole's tested safe yield.
- Total head: the height the pump must push water. That is the pumping water level (static level plus drawdown), plus the height of the tank, plus friction losses in the pipe.
- Water quality: salty, acidic, iron-rich or sandy water decides the pump materials and type.
A common mistake is sizing the pump from the static water level (the level when the pump is off). Once pumping starts, the level drops, sometimes by tens of metres in low-yield boreholes, and a pump sized for the static level will under-perform or run dry. Use the pump size calculator below for a first estimate.
Submersible pump installation, step by step
- Review the borehole data: depth, casing diameter, static and pumping water levels and safe yield from the test pumping report.
- Size and select the pump from the manufacturer's pump curves for the flow and total head, and choose the motor and power supply.
- Choose the materials: stainless steel pump and motor, uPVC, HDPE or steel riser pipe, drop cable sized for voltage drop, and fittings suited to the water quality.
- Lower the pump on its riser pipe with a stainless steel safety rope, cable ties every few metres and a non-return valve. Set it below the pumping water level and normally above the screen, so water flows past and cools the motor. Fit a flow sleeve where needed.
- Fit the controls: solar controller or starter panel, dry-run protection, a level probe in the borehole and a float switch in the tank.
- Connect the tank and meter: pipework to the tank on its stand, and a water meter to record abstraction for the WRA.
- Commission and hand over: measure flow, pressure and the pumping water level, seal the wellhead and train the owner on simple care.
Solar or electric borehole pump?
Most of Kenya has enough sunshine for solar pumping all year round. A solar borehole pump has no fuel or power bills and pumps through the day into a tank, which stores water for the evening and night. In the sunny lowlands of the north, east and coast, solar is almost always the cheapest option. In the cloudier highlands, such as Kericho, Nyandarua, Kisii and Kakamega, solar still works if the array is sized with a margin and the tank holds water for cloudy days.
AC submersible pumps on grid power suit large estates, factories, hotels and institutions that need high flows or water around the clock. A hybrid controller can run one pump from both solar and grid power. You can check the sunshine at your exact site on the Global Solar Atlas (see references).
Kenya's geology and the right pump
The same pump does not suit every part of Kenya. The aquifer type controls the water depth, the yield and the water quality:
| Aquifer | Where | What it means for the pump |
|---|---|---|
| Volcanic rocks | Nairobi, Kiambu, Nakuru, Kajiado, Narok | Water is often deep, so you need high-head multistage pumps. Fluoride is often high. Warm water near volcanic centres needs a suitably rated motor. |
| Basement rocks | Machakos, Kitui, Makueni, Kakamega, Samburu | Yields are modest and drawdown is large. Size the pump to the safe yield, fit dry-run protection and use bigger tanks. |
| Sedimentary basins | Garissa, Wajir, Mandera | Water is deep, warm and often salty. Use stainless steel pumps and long drop cables sized for voltage drop. |
| Coastal coral and sands | Mombasa, Kilifi, Kwale, Lamu | Fresh water floats on salt water. Use small pumps at low, steady rates, set no deeper than needed, with corrosion-resistant materials. |
| River sands | Tana River, Turkana | Water is shallow, but the borehole can produce sand. Use sand-tolerant pumps, good screens and flood-proof wellheads. |
Water quality and pump materials
Water quality decides how long a pump lasts. Salty or mineralised water (common in the north-east, Kitui, Makueni and the coast) corrodes ordinary steel, so choose stainless steel pumps, motors and fittings. Iron-rich water (common around Lake Victoria) leaves deposits on the intake and pipes. Sand wears impellers. Fluoride (common in the Rift Valley and Nairobi) does not harm the pump, but the water needs treatment before drinking. We test the water before choosing the pump.
WRA permits and water meters
Under the Water Act 2016 and the Water Resources Regulations 2021, you need a Water Resources Authority (WRA) permit to abstract groundwater. Permit holders must measure and record the water they abstract, and the WRA increasingly requires smart meters. In 2025 the WRA warned it would act against tens of thousands of operators abstracting water illegally. We install a water meter with every pump, and can help with the permit as part of our borehole drilling service.
Borehole pump repair and maintenance
We pull, test, repair and replace borehole pumps anywhere in Kenya. Common problems include:
- Low flow or no water: a worn pump, a blocked intake, a leaking riser pipe or a falling water level
- The pump keeps tripping: dry running, unstable voltage, a damaged cable or a failing motor
- Sand or dirty water: a damaged screen, or the pump set too low
- Weak solar pumping: dirty or shaded panels, loose connections or a faulty controller
A yearly check of the flow, the water level, the electrical readings and the panels catches most problems before the pump fails.
What affects the cost of borehole pump installation?
The cost depends on the pump setting depth and total head, the flow you need, the power source (a solar array, grid or hybrid), the distance and height to the tank and the water quality, which sets the materials. A small solar pump for a home on a shallow borehole costs far less than a deep, high-flow pump for an estate or farm. Send us your test pumping report and site details for a quotation.
Borehole pump installation in every county of Kenya
Choose your county to see how its geology and water quality affect pump choice, and the towns where we install and repair borehole pumps.
Frequently asked questions
How much does borehole pump installation cost in Kenya?
It depends on the pump setting depth and total head, the flow needed, solar or grid power, the distance and height to the tank and the water quality. Send us your test pumping report for a quotation.
What is the difference between a borehole pump and a submersible pump?
Most borehole pumps in Kenya are submersible pumps: a pump and motor that hang inside the borehole below the water level and push water up to the surface. Surface pumps can only lift water from a few metres down, so they rarely suit boreholes.
Which is the best borehole pump in Kenya?
There is no single best pump. The right pump matches your borehole's safe yield, total head and water quality. A well-sized pump from an established manufacturer, installed correctly, lasts far longer than a cheap or oversized one.
How long does a borehole pump last?
A well-sized, well-installed stainless steel submersible pump commonly lasts many years. Dry running, sand, salty water and voltage problems are the main causes of early failure.
Can I install a solar pump on an existing borehole?
Yes. We can replace a diesel or grid pump with a solar pump, or add a hybrid controller, after checking the borehole's yield and water level.
Do I need a water meter on my borehole?
Yes. Water Resources Authority permit conditions require borehole owners to measure the water they abstract, and we install a meter with every pump.
References and further reading
- Water Resources Authority: water use allocation and permits
- Water Resources Regulations, 2021 (Legal Notice 43 of 2021), Kenya Law
- Grundfos Ecademy: pump sizing and installation in domestic groundwater applications
- Xylem: 5 mistakes when selecting a borehole pump
- Energypedia: Solar Pumping Toolkit, guidance and assessment
- Global Solar Atlas: solar resource map for Kenya
- The Star (2025): WRA warns of rising illegal water abstraction
⚙️ Borehole pump size calculator
Enter your borehole's numbers from the test pumping report (or your best estimate) to see the total head, the flow and roughly how big a submersible pump or solar array you need.
Rough planning figures only. Total head = pumping water level + tank height + an allowance for pipe friction. The final pump is chosen from the manufacturer's pump curves, your test pumping yield and your water quality.
Send these numbers on WhatsAppGet a borehole pump installation quote
Send us your test pumping report, borehole depth and where the tank will sit. We will size the right submersible or solar pump and send a quotation for supply, installation and commissioning.